View PCD5003_108472.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

INTEGRATED CIRCUITS
DATA SHEET
PCD5003 Advanced POCSAG Paging Decoder
Product specification Supersedes data of 1997 Mar 04 File under Integrated Circuits, IC17 1997 Jun 24
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
CONTENTS FEATURES 2 3 4 5 6 7 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 7.11 7.12 7.13 7.14 7.15 7.16 7.17 7.18 7.19 7.20 7.21 7.22 7.23 7.24 7.25 7.26 7.27 7.28 7.29 7.30 7.31 7.32 7.33 7.34 7.35 7.36 7.37 7.38 7.39 7.40 7.41 7.42 APPLICATIONS GENERAL DESCRIPTION ORDERING INFORMATION BLOCK DIAGRAM PINNING FUNCTIONAL DESCRIPTION Introduction The POCSAG paging code Error correction Operating states ON status OFF status Reset Bit rates Oscillator Input data processing Battery saving Synchronization strategy Call termination Call data output format Sync word indication Error type indication Data transfer Receiver and oscillator control External receiver control and monitoring Battery condition input Synthesizer control Serial microcontroller interface Decoder I2C-bus access External interrupt Status/Control register Pending interrupts Out-of-Range Indication Real time clock Periodic interrupt Received call delay Alert generation Alert cadence register (03H; write) Acoustic alert Vibrator alert LED alert Warbled alert Direct alert control Alert priority Cancelling alerts Automatic POCSAG alerts SRAM access RAM write address pointer (06H; read) 2 7.43 7.44 7.45 7.46 7.47 7.48 7.49 7.50 7.51 7.52 7.53 7.54 7.55 7.56 7.57 7.58 7.59 8 8.1 8.2 8.3 8.4 9 10 11 12 13 14 15 16 17 17.1 17.2 17.3 17.4 18 19 20
PCD5003
RAM read address pointer (08H; read/write) RAM data output register (09H; read) EEPROM access EEPROM address pointer (07H; read/write) EEPROM data I/O register (0AH; read/write) EEPROM access limitations EEPROM read operation EEPROM write operation Invalid write address Incomplete programming sequence Unused EEPROM locations Special programmed function allocation Synthesizer programming data Identifier storage allocation Voltage doubler Level-shifted interface Signal test mode OPERATING INSTRUCTIONS Reset conditions Power-on reset circuit Reset timing Initial programming LIMITING VALUES DC CHARACTERISTICS DC CHARACTERISTICS (WITH VOLTAGE CONVERTER) OSCILLATOR CHARACTERISTICS EEPROM CHARACTERISTICS AC CHARACTERISTICS APPLICATION INFORMATION PACKAGE OUTLINE SOLDERING Introduction Reflow soldering Wave soldering Repairing soldered joints DEFINITIONS LIFE SUPPORT APPLICATIONS PURCHASE OF PHILIPS I2C COMPONENTS
1997 Jun 24
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
1 FEATURES
PCD5003
* On-chip SRAM buffer for message data * Slave I2C-bus interface to microcontroller for transfer of message data, status/control and EEPROM programming (data transfer at up to 400 kbits/s) * Wake-up interrupt for microcontroller, programmable polarity * Direct and I2C-bus control of operating status (ON/OFF) * Battery-low indication (external detector) * Out-of-range condition indication * Real time clock reference output * On-chip voltage doubler * Interfaces directly to UAA2080 and UAA2082 paging receivers. 2 APPLICATIONS
* Wide operating supply voltage range: 1.5 to 6.0 V * EEPROM programming requires only 2.0 V supply * Low operating current: 50 A typ. (ON), 25 A typ. (OFF) * Temperature range: -25 to +70 C * "CCIR Radio paging Code No. 1" (POCSAG) compatible * 512, 1200 and 2400 bits/s data rates using 76.8 kHz crystal * Built-in data filter (16-times oversampling) and bit clock recovery * Advanced ACCESS(R) synchronization algorithm * 2-bit random and (optional) 4-bit burst error correction * Up to 6 user addresses (RICs), each with 4 functions/alert cadences * Up to 6 user address frames, independently programmable * Standard POCSAG sync word, plus up to 4 user programmable sync words * Received data inversion (optional) * Call alert via beeper, vibrator or LED * 2-level acoustic alert using single external transistor * Alert control: automatic (POCSAG type), via cadence register or alert input pin * Separate power control of receiver and RF-oscillator for battery economy * Synthesizer set-up and control interface (3-line serial) * On-chip EEPROM for storage of user addresses (RICs), pager configuration and synthesizer data 4 ORDERING INFORMATION TYPE NUMBER PCD5003H PCD5003U/10
* Display pagers, basic alert-only pagers * Information services * Personal organizers * Telepoint * Telemetry/data transmission. 3 GENERAL DESCRIPTION
The PCD5003 is a very low power POCSAG decoder and pager controller. It supports data rates of 512, 1200 and 2400 bits/s using a single 76.8 kHz crystal. On-chip EEPROM is programmable using a minimum supply voltage of 2.0 V, allowing `over-the-air' programming. The PCD5003 is fast I2C-bus compatible (maximum 400 kbits/s).
PACKAGE NAME LQFP32 - DESCRIPTION plastic low profile quad flat package; 32 leads; body 7 x 7 x 1.4 mm film-frame carrier (naked die) 32 pads VERSION SOT358-1 -
1997 Jun 24
3
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
5 BLOCK DIAGRAM
PCD5003
handbook, full pagewidth
EEPROM ZSD ZSC ZLE 26 27 28 SYNTHESIZER CONTROL
RESET SET-UP
7
RST
EEPROM CONTROL
9 I 2 C-BUS CONTROL 10
SDA SCL
RXE ROE
24 25 RECEIVER CONTROL
DECODING DATA CONTROL
POCSAG SYNCHRONIZATION REGISTERS AND INTERRUPT CONTROL
5
INT
RDI
23
DATA FILTER AND CLOCK RECOVERY
RAM CONTROL MAIN DECODER
21
BAT
30 RAM 31 ALERT GENERATION AND CONTROL 1 32 2
VIB LED ATL ATH ALC REF CCN CCP VPO VPR
DON
3
CLOCK CONTROL
MASTER DIVIDER
TIMER REFERENCE
TS1 TS2 XTAL1 XTAL2
16 20 18 17 OSCILLATOR 11 VDD TEST CONTROL VOLTAGE DOUBLER AND LEVEL SHIFTER 12, 29
4 15 14 13 8
PCD5003
MLC244
VSS
Fig.1 Block diagram.
1997 Jun 24
4
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
6 PINNING DESCRIPTION alert LOW level output alert control input (normally LOW by internal pull-down) direct ON/OFF input (normally LOW by internal pull-down) real time clock frequency reference output interrupt output not connected reset input (normally LOW by internal pull-down)
PCD5003
SYMBOL PIN ATL ALC DON REF INT n.c. RST VPR SDA SCL VDD VSS VPO CCP CCN TS1 XTAL2 XTAL1 n.c. TS2 BAT n.c. RDI RXE ROE ZSD ZSC ZLE VSS VIB LED ATH 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
I2C-bus serial data input/output I2C-bus serial clock input main positive supply voltage main negative supply voltage voltage converter positive output voltage converter shunt capacitor (positive side) voltage converter shunt capacitor (negative side) test input 1 (normally LOW by internal pull-down) decoder crystal oscillator output decoder crystal oscillator input not connected test input 2 (normally LOW by internal pull-down) battery sense input not connected received POCSAG data input receiver circuit enable output receiver oscillator enable output synthesizer serial data output synthesizer serial clock output synthesizer latch enable output main negative supply voltage vibrator motor drive output LED drive output alert HIGH level output
ATL ALC DON REF INT n.c. RST VPR 1 2 3 4 5 6 7 8
25 ROE
32 ATH
27 ZSC
26 ZSD
31 LED
29 VSS
28 ZLE
30 VIB
external positive voltage reference input
24 RXE 23 RDI 22 n.c. 21 BAT
PCD5003H
20 TS2 19 n.c. 18 XTAL1 17 XTAL2
SCL 10
VDD 11
VSS 12
VPO 13
CCP 14
CCN 15
TS1 16
9
MLC245
Fig.2 Pin configuration for SOT358-1 (LQFP32).
1997 Jun 24
5
SDA
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
7 7.1 FUNCTIONAL DESCRIPTION Introduction
PCD5003
between the devices. Pager status includes features provided by the PCD5003 such as battery-low and out-of-range indications. A dedicated interrupt line minimizes the required microcontroller activity. A selectable low frequency timing reference is provided for use in real time clock functions. Data synchronization is achieved by the Philips patented ACCESS(R) algorithm ensuring that maximum advantage is made of the POCSAG code structure particularly in fading radio signal conditions. The algorithm allows for data synchronization without preamble detection whilst minimizing battery power consumption. Random and (optional) burst error correction techniques are applied to the received data to optimize on call success rate without increasing falsing rate beyond specified POCSAG levels. 7.2 The POCSAG paging code
The PCD5003 is a very low power decoder and pager controller specifically designed for use in new generation radio pagers. The architecture of the PCD5003 allows for flexible application in a wide variety of radio pager designs. The PCD5003 is fully compatible with "CCIR Radio paging Code No. 1" (also known as the POCSAG code) operating at data rates of 512, 1200 and 2400 bits/s using a single oscillator crystal of 76.8 kHz. In addition to the standard POCSAG sync word the PCD5003 is also capable of recognizing up to 4 User Programmable Sync Words (UPSWs). This permits the reception of both private services and POCSAG transmissions via the same radio channel. Used together with the Philips UAA2080 or UAA2082 paging receiver, the PCD5003 offers a highly sophisticated, miniature solution for the radio paging market. Control of an RF synthesizer circuit is also provided to ease alignment and channel selection. On-chip EEPROM provides storage for user addresses (Receiver Identity Codes or RICs) and Special Programmed Functions (SPFs), which eliminates the need for external storage devices and interconnection. For other non-volatile storage 20 bytes of general purpose EEPROM are available. The low EEPROM programming voltage makes the PCD5003 well- suited for `over-the-air' programming/reprogramming. On request from an external controlling device or automatically (by SPF programming), the PCD5003 will provide standard POCSAG alert cadences by driving a standard acoustic `beeper'. Non-standard alert cadences may be generated via a cadence register or a dedicated control input. The PCD5003 can also produce a HIGH level acoustic alert as well as drive an LED indicator and a vibrator motor via external bipolar transistors. The PCD5003 contains a low-power, high-efficiency voltage converter (doubler) designed to provide a higher voltage supply to LCD drivers or microcontrollers. In addition, an independent level shifted interface is provided allowing communication to a microcontroller operating at a higher voltage than the PCD5003. Interface to such an external device is provided by an I2C-bus which allows received call identity and message data, data for the programming of the internal EEPROM, alert control and pager status information to be transferred
A transmission using the "CCIR Radio paging Code No. 1" (POCSAG code) is constructed in accordance with the following rules (see Fig.3). The transmission is started by sending a preamble, consisting of at least 576 continuously alternating bits (10101010...). The preamble is followed by an arbitrary number of batch blocks. Only complete batches are transmitted. Each batch comprises 17 codewords of 32 bits each. The first codeword is a synchronization codeword with a fixed pattern. The sync word is followed by 8 frames (0 to 7) of 2 codewords each, containing message information. A codeword in a frame can either be an address, message or idle codeword. Idle codewords also have a fixed pattern and are used to fill empty frames or to separate messages. Address codewords are identified by an MSB of logic 0 and are coded as shown in Fig.3. A user address or RIC consists of 21 bits. Only the upper 18 bits are encoded in the address codeword (bits 2 to 19). The lower 3 bits designate the frame number (0 to 7) in which the address is transmitted. Four different call types (`numeric', `alphanumeric' and two `alert only' types) can be distinguished on each user address. The call type is determined by two function bits in the address codeword (bits 20 and 21), as shown in Table 1.
1997 Jun 24
6
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
Alert-only calls only consist of a single address codeword. Numeric and alphanumeric calls have message codewords following the address. A message causes the frame structure to be temporarily suspended. Message codewords are sent until the message is completed, with only the sync words being transmitted in their expected positions. Message codewords are identified by an MSB of logic 1 and are coded as shown in Fig.3. The message information is stored in a 20-bit field (bits 2 to 21). The data format is determined by the call type: 4 bits per digit for numeric messages and 7 bits per (ASCII) character for alphanumeric messages.
PCD5003
Each codeword is protected against transmission errors by 10 CRC check bits (bits 22 to 31) and an even-parity bit (bit 32). This permits correction of maximum 2 random errors or up to 3 errors in a burst of 4 bits (a 4-bit burst error) per codeword. The POCSAG standard recommends the use of combinations of data formats and function bits, as given in Table 1. Other (non-standard) combinations will be received normally by the PCD5003. Message data is not deformatted.
handbook, full pagewidth
PREAMBLE
BATCH 1
BATCH 2
BATCH 3
LAST BATCH
10101 . . . 10101010
SYNC | CW CW | CW CW | . . . . . | CW CW
FRAME 0 FRAME 1 FRAME 7
Address code-word
0
18-bit address
2 function bits
10 CRC bits
P
Message code-word
1
20-bit message
10 CRC bits
P
MCD456
Fig.3 POCSAG code structure.
Table 1
POCSAG recommended call types and function bits BIT 20 (MSB) 0 0 1 1 BIT 21 (LSB) 0 1 0 1 CALL TYPE numeric alert only 1 alert only 2 alphanumeric DATA FORMAT 4-bits per digit - - 7-bits per ASCII character
1997 Jun 24
7
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
7.3 Error correction Error correction ITEM Preamble Synchronization codeword Address codeword Message codeword In the PCD5003 error correction methods have been implemented as shown in Table 2. Random error correction is default for both address and message codewords. In addition, burst error correction can be enabled by SPF programming. Up to 3 erroneous bits in a 4-bit burst can be corrected. The error type detected for each codeword is identified in the message data output to the microcontroller, allowing rejection of calls with too many errors. 7.4 Operating states DESCRIPTION 4 random errors in 31 bits 2 random errors in 32 bits
PCD5003
Table 2
2 random errors, plus: 4-bit burst errors (optional) 2 random errors, plus: 4-bit burst errors (optional) 7.6 OFF status
In OFF status the decoder will neither activate the receiver or oscillator enable outputs, nor process any data at the data input. The crystal oscillator remains active to permit communication with the microcontroller. In both operating states an accurate timing reference is available via the REF output. By SPF programming the signal periodicity may be selected as 32.768 kHz, 50 Hz, 2 Hz or 160 Hz. 7.7 Reset
The PCD5003 has 2 operating states: * ON status * OFF status. The operating state is determined by a Direct Control input (DON) and bit D4 in the control register (see Table 3). Table 3 Truth table for decoder operating status CONTROL BIT D4 0 1 0 1 OPERATING STATUS OFF ON ON ON
The decoder can be reset by applying a positive pulse on input pin RST. A power-on reset circuit consisting of an RC network can be connected to this input as well. Conditions during and after a reset are described in Chapter "Operating instructions". For successful reset at power-on, a HIGH level must be present on the RST pin while the device is powering-up. This can be applied by the microcontroller, or via a suitable RC power-on reset circuit connected to the RST input. Reset circuit details and conditions during and after a reset are described in Chapter 8 7.8 Bit rates
DON INPUT 0 0 1 1 7.5 ON status
The PCD5003 can be configured for data rates of 512, 1200 or 2400 bit/s by SPF programming. These data rates are derived from a single 76.8 kHz oscillator frequency. 7.9 Oscillator
In ON status the decoder pulses the receiver and oscillator enable outputs (respectively RXE and ROE) according to the code structure and the synchronization algorithm. Data received serially at the data input (RDI) is processed for call receipt. Reception of a valid paging call is signalled to the microcontroller by means of an interrupt signal. The received address and message data can then be read via the I2C-bus interface.
The oscillator circuit is designed to operate at 76.8 kHz. Typically, a tuning fork crystal will be used as a frequency source. Alternatively, an external clock signal can be applied to pin XTAL1 (amplitude = VDD to VSS), but a slightly higher oscillator current is consumed. A 2.2 M feedback resistor connected between XTAL1 and XTAL2 is required for proper operation.
1997 Jun 24
8
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
To allow easy oscillator adjustment (e.g. by means of a variable capacitor) a 32.768 kHz reference frequency can be selected at output REF by SPF programming. 7.10 Input data processing
PCD5003
appropriate establishment times (respectively tRXON and tROON). Before comparing received data with preamble, an enabled sync word or programmed user addresses, the appropriate error correction is applied. Initially, after switching to ON status, the decoder is in switch-on mode. Here the receiver will be enabled for a period up to 3 batches, testing for preamble and sync word. Failure to detect preamble or sync word will cause switching to `carrier off' mode. Detection of preamble switches to preamble receive mode, in which sync word is looked for. The receiver will remain enabled while preamble is detected. When neither sync word nor preamble is found within 1 batch duration `carrier off' mode is entered. Upon detection of a sync word the data receive mode is entered. The receiver is activated only during enabled user address frames and sync word periods. When an enabled user address has been detected, the receiver will be kept enabled for message codeword reception until the call termination criteria are met. During call reception data bytes are stored in an internal SRAM buffer, capable of storing 2 batches of message data. Messages are transmitted contiguously, only interrupted by sync words at the beginning of each batch. When a message extends beyond the end of a batch, no testing for sync takes place. Instead, a message data transfer will be initiated by an interrupt to the external controller. Data reception continues normally after a period corresponding to the sync word duration. If any message codeword is found to be uncorrectable, `data-fail' mode is entered and no data transfer will be attempted at the next sync word position. Instead, a test for sync word will be carried out. In the data fail mode message reception continues normally for 1 batch duration. Upon detection of sync word at the expected position the decoder returns to `data receive' mode. If sync word again fails to appear, batch synchronization is deemed lost. Call reception is then terminated and `fade recovery' mode is entered. The fade recovery mode is intended to scan for sync word and preamble over an extended window (nominal position 8 bits).
Data input is binary and fully asynchronous. Input bit rates of 512, 1200 and 2400 bits/s are supported. As a programmable option, the polarity of the received data can be inverted before further processing. The input data is noise filtered by means of a digital filter. Data is sampled at 16 times the data rate and averaged by majority decision. The filtered data is used to synchronize an internal clock generator by monitoring transitions. The recovered clock phase can be adjusted in steps of 18 or 132 bit period per received bit. The larger step size is used when bit synchronization has not been achieved, the smaller when a valid data sequence has been detected (e.g. preamble or sync word). 7.11 Battery saving
Current consumption is reduced by switching off internal decoder sections whenever the receiver is not enabled. To further increase battery efficiency, reception and decoding of an address codeword is stopped as soon as the uncorrected address field differs by more than 3 bits from the enabled RICs. If the next codeword must be received again, the receiver is re-enabled thus observing the programmed establishment times tRXE and tRDE. The current consumption of the complete pager can be minimized by separately activating the RF oscillator circuit (at output ROE) before activating the rest of the receiver. This is possible with the UAA2082 receiver which has external biasing for the oscillator circuit. 7.12 Synchronization strategy
In ON status the PCD5003 synchronizes to the POCSAG data stream by means of the Philips ACCESS(R) algorithm. A flow diagram is shown in Fig.4. Where `sync word' is used, this implies both the standard POCSAG sync word and any enabled User Programmable Sync Word (UPSW). Several modes of operation can be distinguished depending on the synchronization state. Each mode uses a different method to obtain or retain data synchronization. The receiver and oscillator enable outputs (respectively RXE and ROE) are switched accordingly, with the 1997 Jun 24 9
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
This is done for a period of up to 15 batches, allowing recovery of synchronization from long fades in the radio signal. Detection of preamble switches to `preamble receive' mode, while sync word detection switches to `data receive' mode. When neither is found within a period of 15 batches, the radio signal is considered lost and `carrier off' mode is entered. The purpose of carrier off mode is to detect a valid radio transmission and synchronize to it quickly and efficiently. Because transmissions may start at random, the decoder enables the receiver for 1 codeword in every 18 codewords looking for preamble or sync word. By using a buffer containing 32 bits (n bits from the current scan, 32 - n from the previous scan) effectively every batch bit position can be tested within a continuous transmission of at least 18 batches. Detection of preamble switches to `preamble receive' mode, while sync word detection switches to `data receive' mode. 7.13 Call termination
PCD5003
The formats of a call header, a message data block and a call terminator are shown in Tables 4, 6 and 8. A Call Header contains information on the last sync word received, the RIC which began call reception and the type of error correction performed on the address codeword. A Message Data block contains the data bits from a message codeword plus the type of error correction performed. No deformatting is done on the data bits: numeric data appear as 4-bit groups per digit, alphanumeric data have a 7-bit ASCII representation. The Call Terminator contains information on the last sync word received, information on the way the call was terminated (forced call termination command, loss of sync word in `data fail' mode) and the type of error correction performed on the terminating codeword. 7.15 Sync word indication
Call reception is terminated: * Upon reception of any address codeword (including Idle codeword) requiring no more than single bit error correction * In `data fail' mode, when a sync word is not found at the expected batch position * When a forced call termination command is received from an external controller. The last method permits an external controller to stop call reception depending on the number and type of errors which occurred in a call. After a forced call termination the decoder will enter `data fail' mode. The type of error correction as well as the call termination conditions are indicated by status bits in the message data output. Following call termination, transfer of the data received since the previous sync word period is initiated by means of an interrupt to the external controller. 7.14 Call data output format
The sync word recognized by the PCD5003 is shown in the call header (bits S3 to S1). The decimal value represents the identifier number in the EEPROM of the UPSW in question. A value of 7 indicates the standard POCSAG sync word. 7.16 Error type indication
Table 10 shows how the different types of detected errors are encoded in the call data output format. A message codeword containing more than a single bit error (bit E3 = 1) may appear as an address codeword (bit M1 = 0) after error correction. In this event the codeword is processed as message data and does not cause call termination. 7.17 Data transfer
Data transfer is initiated either during sync word periods or as soon as the receiver is disabled after call termination. If the SRAM buffer is full, data transfer is initiated immediately during the next codeword. When the PCD5003 is ready to transfer received call data an external interrupt will be generated via output INT. Any message data can be read by accessing the RAM output register via the I2C-bus interface. Bytes will be output starting from the position indicated by the RAM read pointer.
POCSAG call information is stored in the decoder SRAM in blocks of 3 bytes per codeword. Each stored call consists of a call header, followed by message data blocks and concluded by a call terminator. In the event of concatenated messages the call terminator is replaced with the call header of the next message. An alert-only call only has a call header and a call terminator.
1997 Jun 24
10
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
PCD5003
handbook, full pagewidth
OFF to ON status no preamble or sync word (3 batches) sync word no preamble or sync word (1 batch)
switch-on preamble
preamble receive sync word
data receive sync word no sync word preamble
data fail
no preamble or sync word (1 batch) sync word fade recovery preamble
no preamble or sync word (15 batches) sync word carrier off preamble
MLC247
Fig.4 ACCESS(R) synchronization algorithm.
1997 Jun 24
11
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
Table 4 Call header format BIT 7 (MSB) 0 0 X BIT 6 S3 S3 X BIT 5 S2 S2 F0 BIT 4 S1 S1 F1 BIT 3 R3 R3 E3 BIT 2 R2 R2 E2
PCD5003
BYTE NUMBER 1 2 3 Table 5
BIT 1 R1 R1 E1
BIT 0 (LSB) DF 0 0
Call header bit identification IDENTIFICATION identifier number of sync word for current batch (7 = standard POCSAG) identifier number of user address (RIC) data fail mode indication (1 = data fail mode); note 1 function bits of received address codeword (bits 20, 21) detected error type; see Table 10; E3 = 0 in a concatenated call header
BITS (MSB to LSB) S3 to S1 R3 to R1 DF F0 and F1 E3 to E1 Note 1. The DF bit in the call header is set:
a) When the sync word of the batch in which the (beginning of the) call was received, did not match the standard POCSAG or a user-programmed sync word. The sync word identifier (bits S3 to S1) will then be made 0. b) When any codeword of a previous call received in the same batch was uncorrectable. Table 6 Message data format BIT 7 (MSB) M2 M10 M18 BIT 6 M3 M11 M19 BIT 5 M4 M12 M20 BIT 4 M5 M13 M21 BIT 3 M6 M14 E3 BIT 2 M7 M15 E2 BIT 1 M8 M16 E1 BIT 0 (LSB) M9 M17 M1
BYTE NUMBER 1 2 3 Table 7
Message data bit identification IDENTIFICATION message codeword data bits detected error type; see Table 10 message codeword flag
BITS (MSB to LSB) M2 to M21 E3 to E1 M1 Table 8 Call terminator format BIT 7 (MSB) FT FT X BIT 6 S3 S3 X BIT 5 S2 S2 X BIT 4 S1 S1 X
BYTE NUMBER 1 2 3
BIT 3 0 0 E3
BIT 2 0 0 E2
BIT 1 0 0 E1
BIT 0 (LSB) DF X 0
1997 Jun 24
12
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
Table 9 Call terminator bit identification BITS (MSB to LSB) FT S3 to S1 DF E3 to E1 Note 1. The DF bit in the call terminator is set: IDENTIFICATION forced call termination (1 = yes) identifier number of last sync word data fail mode indication (1 = data fail mode); note 1 detected error type; see Table 10; E3 = 0 in a call terminator
PCD5003
a) When any call data codeword in the terminating batch was uncorrectable, while in `data receive' mode. b) When the sync word at the start of the terminating batch did not match the standard POCSAG or a user-programmed sync word, while in `data fail' mode. Table 10 Error type identification (note 1) E3 0 0 0 0 1 1 1 1 Note 1. POCSAG code allows a maximum of 3 bit errors to be detected per codeword. Successful call termination occurs by reception of a valid address codeword with less than 2 bit errors. Unsuccessful termination occurs when sync word is not detected while in `data fail' mode. It is generally possible to distinguish these two conditions using the sync word identifier number (bits S3 to S1); the identifier number will be non-zero for correct termination, and zero for sync word failure. Only when a call is received in `data fail' mode and the call is terminated before the end of the batch, is it not possible to distinguish unsuccessful from correct termination. Reception of message data can be terminated at any time by transmitting a forced call termination command to the control register via the I2C-bus. Any call received will then be terminated immediately and `data fail' mode will be entered. 7.18 Receiver and oscillator control E2 0 0 1 1 0 0 1 1 E1 0 1 0 1 0 1 0 1 ERROR TYPE no errors - correct codeword parity bit in error single bit error single bit error and parity error not used 4-bit burst error and parity error 2-bit random error uncorrectable codeword 3 (e.g.1101) 2 3 or more 0 1 1 + parity 1 NUMBER OF ERRORS
A paging receiver and an RF oscillator circuit can be controlled independently via enable outputs RXE and ROE respectively. Their operating periods are optimized according to the synchronization mode of the decoder. Each enable signal has its own programmable establishment time (see Table 11). 7.19 External receiver control and monitoring
An external controller may enable the receiver control outputs continuously via an I2C-bus command, overruling the normal enable pattern. Data reception continues normally. This mode can be left by means of a reset or an I2C-bus command. External monitoring of the receiver control output RXE is possible via bit D6 in the status register, when enabled via the control register (D2 = 1). Each change of state of output RXE will generate an external interrupt at output INT. 13
1997 Jun 24
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
7.20 Battery condition input
PCD5003
copies the data to the internal divider registers. A timing diagram is given in Fig.5. The data output timing is synchronous, but has a pause in the bit stream of each block. This pause occurs in the 13th bit while ZSC is LOW. The nominal pause duration tp depends on the programmed bit rate for data reception and is shown in Table 12. The total duration of the 13th bit is given by tZCL + tp. A similar pause occurs between the first and the second data block. The delay between the first latch enable pulse and the second data block is given by tZDL2 + tp. The complete start-up timing of the synthesizer interface is given in Fig.12. Table 12 Synthesizer programming pause BIT RATE (bit/s) 512 1200 2400 7.22 tp (clocks) 119 33 1 tp (s) 1549 430 13
A logic signal from an external sense circuit signalling battery condition can be applied to the BAT input. This input is sampled each time the receiver is disabled (RXE 0). When enabled via the control register (D2 = 0), the condition of input BAT is reflected in bit D6 of the status register. Each change of state of bit D6 causes an external interrupt at output INT. When using the UAA2080 pager receiver a battery-low condition corresponds to a logic HIGH-level. With a different sense circuit the reverse polarity can be used as well, because every change of state is signalled to an external controller. After a reset the initial condition of the battery-low indicator in the status register is zero. Table 11 Receiver and oscillator establishment times (note 1) CONTROL OUTPUT RXE ROE Note 1. The exact values may differ slightly from the above values, depending on the bit rate (see Table 22). 7.21 Synthesizer control ESTABLISHMENT TIME 5 20 10 30 15 40 30 50 UNIT ms ms
Serial microcontroller interface
The PCD5003 has an I2C-bus serial microcontroller interface capable of operating at 400 kbits/s. The PCD5003 is a slave transceiver with a 7-bit I2C-bus address 39 (bits A6 to A0 = 0100111). Together with the R/W bit the first byte of an I2C-bus message then becomes 4EH (write) or 4FH (read). Data transmission requires 2 lines: SDA (data) and SCL (clock), each with an external pull-up resistor. The clock signal (SCL) for any data transmission must be generated by the external controlling device. A transmission is initiated by a start condition (S: SCL = 1, SDA = ) and terminated by a stop condition (P: SCL = 1, SDA = ). Data bits must be stable when SCL is HIGH. If there are multiple transmissions, the stop condition can be replaced with a new start condition. Data is transferred on a byte basis, starting with a device address and a read/write indicator. Each transmitted byte must be followed by an acknowledge bit ACK (active LOW). If a receiving device is not ready to accept the next complete byte, it can force a bus wait state by holding SCL LOW. The general I2C-bus transmission format is shown in Fig.6. Formats for master/slave communication are shown in Fig.7.
Control of an external frequency synthesizer is possible via a dedicated 3-line serial interface (outputs ZSD, ZSC and ZLE). This interface is common to a number of available synthesizers. The synthesizer is enabled using the oscillator enable output ROE. The frequency parameters must be programmed in EEPROM. Two blocks of maximum 24 bits each can be stored. Any unused bits must be programmed at the beginning of a block: only the last bits are used by the synthesizer. When the function is selected by SPF programming (SPF byte 01, bit D6), data is transferred to the synthesizer each time the PCD5003 is switched from OFF to ON status. Transfer takes place serially in two blocks, starting with bit 0 (MSB) of block 1 (see Table 25). Data bits on ZSD change on the falling flanks of ZSC. After clocking all bits into the synthesizer, a latch enable pulse
1997 Jun 24
14
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
PCD5003
handbook, full pagewidth
MSB ZSD 0
t ZSD
LSB 12 23
ZSC TIME t ZCL ZLE TIME t ZLE t ZDS tp t ZDL1
MLC248
Fig.5 Synthesizer interface timing.
handbook, full pagewidth
MSB
LSB
N A
MSB
LSB
N A
SDA
S
P
SCL
1
2
7
8
9
INTERRUPT SERVICING 1
2
7
8
9
START
ADDRESS
R/W A
DATA
A
STOP
MLC249
Fig.6 I2C-bus message format.
1997 Jun 24
15
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
PCD5003
handbook, full pagewidth
FROM MASTER
FROM SLAVE
S = START condition P = STOP condition
A = Acknowledge N = Not acknowledge
(a)
S
SLAVE ADDRESS
R/W 0 (write)
A
INDEX index address
A
DATA
A
DATA
A
P
n bytes with acknowledge
(b)
S
SLAVE ADDRESS
R/W 1 (read)
A
DATA
A
DATA
N
P
n bytes with acknowledge
(c)
S
SL. ADR.
R/W 0 (write)
A
INDEX index address
A
DATA
A
S
SL. ADR.
R/W 1 (read)
A
DATA
N
P
n bytes with acknowledge
change of direction
n bytes with acknowledge
MLC250
(a) Master writes to slave. (b) Master reads from slave. (c) Combined format (shown: write plus read).
Fig.7 Message types.
7.23
Decoder I2C-bus access
All internal access to the PCD5003 takes place via I2C-bus interface. For this purpose the internal registers, SRAM and EEPROM have been memory mapped and are accessed via an index register. Table 13 shows the index addresses of all internal blocks. Registers are addressed directly, while RAM and EEPROM are addressed indirectly via address pointers and I/O registers. Remark: The EEPROM memory map is non-contiguous and organized as a matrix. The EEPROM address pointer contains both row and column indicators.
Data written to read-only bits will be ignored. Values read from write-only bits are undefined and must be ignored. Each I2C write message to the PCD5003 must start with its slave address, followed by the index address of the memory element to be accessed. An I2C read message uses the last written index address as a data source. The different I2C-bus message types are shown in Fig.7. As a slave the PCD5003 cannot initiate bus transfers by itself. To prevent an external controller from having to monitor the operating status of the decoder, all important events generate an external interrupt on output INT.
1997 Jun 24
16
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
Table 13 Index register ADDRESS(1) 00H 00H 01H 02H 03H 04H 05H 05H 06H 07H 08H 09H 0AH 0BH to 0FH Notes 1. The index register only uses the least significant nibble, the upper 4 bits are ignored. 2. Writing to registers 0B to 0F has no effect, reading produces meaningless data. 7.24 External interrupt real time REGISTER FUNCTION status control real time clock: seconds clock: 1100 second alert cadence alert set-up periodic interrupt modulus periodic interrupt counter RAM write address pointer EEPROM address pointer RAM read address pointer RAM data output EEPROM data input/output unused
PCD5003
ACCESS R W R/W R/W W W W R R R/W R/W R R/W note 2
The PCD5003 can signal events to an external controller via an interrupt signal on output INT. The interrupt polarity is programmable via SPF programming. The interrupt source is shown in the status register. Interrupts are generated by the following events (more than one event possible): * Call data available for output (bit D2) * SRAM pointers becoming equal (bit D3) * Expiry of periodic time-out (bit D7) * Expiry of alert time-out (bit D4) * Change of state in out-of-range indicator (bit D5) * Change of state in battery-low indicator or in receiver control output RXE (bit D6). Immediate interrupts are generated by status bits D3, D4, D6 (RXE monitoring) and D7. Bits D2, D5 and D6 (BAT monitoring) generate interrupts as soon as the receiver is disabled (RXE = 0). When call data is available (D2 = 1) but the receiver remains switched on, an interrupt is generated at the next sync word position.
The interrupt output INT is reset after completion of a status read operation. 7.25 Status/Control register
The status/control register consists of two independent registers, one for reading (status) and one for writing (control). The status register shows the current operating condition of the decoder and the cause(s) of an external interrupt. The control register activates/deactivates certain functions. Tables 14 and 15 show the bit allocations of both registers. All status bits will be reset after a status read operation except for the out-of-range, battery-low and receiver enable indicator bits (see note 1 to Table 14). Status bit D0 is set when call reception is started by detection of an enabled RIC (user address). This does not generate an interrupt.
1997 Jun 24
17
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
Table 14 Status register (00H; read) BIT(1) VALUE 00 D1 and D0 01 10 11 00 D3 and D2 01 10 11 D4 D5 D6 D7 Note 1 1 1 1 no new call data new call received reserved for future use reserved for future use no data to be read (default after reset) RAM read/write pointers different: data to be read RAM read/write pointers equal: no more data to read RAM buffer full or overflow alert time-out expired out-of-range DESCRIPTION
PCD5003
BAT input HIGH or RXE output active (selected by control bit D2) periodic timer interrupt
1. After a status read operation bits D3, D4 and D7 are always reset, bits D1 and D0 only when no second call is pending. D2 is reset when the RAM is empty (read and write pointers equal). Table 15 Control register (00H; write) BIT (MSB: D7) D0 D1 D2 D3 D4 D5 to D7 7.26 Pending interrupts VALUE 1 1 0 1 1 0 1 X DESCRIPTION forced call termination (automatically reset after termination) EEPROM programming enable BAT input selected for monitoring (status bit D6) RXE output selected for monitoring (status bit D6) receiver continuously enabled (RXE = 1, ROE = 1) decoder in OFF status (while DON = 0) decoder in ON status not used: ignored when written 7.27 Out-of-range Indication
A secondary status register is used for storing status bits of pending interrupts. This occurs: * When a new call is received while the previous one was not yet acknowledged by reading the status register * When an interrupt occurs during a status read operation. After completion of the status read the primary register is loaded with the contents of the secondary register, which is then reset. Next, an immediate interrupt is generated, output INT becoming active 1 decoder clock cycle after it was reset following the status read. Remark: In the event of multiple pending calls, only the status bits of the last call are retained. 1997 Jun 24 18
The out-of-range condition occurs when entering fade recovery or `carrier off' mode. This condition is reflected in bit D5 of the status register. The out-of-range condition is reset when either preamble or a valid sync word is detected. The out-of-range bit (D5) in the status register is updated each time the receiver is disabled (RXE 0). Every change of state in bit D5 generates an interrupt.
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
7.28 Real time clock
PCD5003
Table 17 Real time clock; 1100 second register (02H; read/write) BIT (MSB D7) D0 D1 D2 D3 D4 D5 D6 D7 VALUE - - - - - - - X DESCRIPTION 0 01 s 0.02 s 0.04 s 0.08 s 0.16 s 0.32 s 0.64 s not used: ignored when written, undetermined when read
The PCD5003 provides a periodic reference pulse at output REF. The frequency of this signal can be selected by SPF programming: * 32768 Hz * 50 Hz (square-wave) * 2 Hz * 160 Hz. The 32768 Hz signal does not have a fixed period: it consists of 32 pulses distributed over 75 main oscillator cycles at 76.8 kHz. The timing is shown in Fig.14. When programmed for 160 Hz (1 pulse per minute) the pulse at output REF is held off while the receiver is enabled. Except for the 50 Hz frequency the pulse width tRFP is equal to one decoder clock period. The real time clock counter runs continuously irrespective of the operating condition of the PCD5003. It contains a seconds register (maximum 59) and a 1100 second register (maximum 99), which can be read or written via the I2C-bus. The bit allocation of both registers is shown in Tables 16 and 17. Table 16 Real time clock; seconds register (01H; read/write) BIT (MSB D7) D0 D1 D2 D3 D4 D5 D6 D7 VALUE - - - - - - X X DESCRIPTION 1s 2s 4s 8s 16 s 32 s not used: ignored when written, undetermined when read not used: ignored when written, undetermined when read
7.29
Periodic interrupt
A periodic interrupt can be realised with the Periodic Interrupt Counter. This 8-bit counter is incremented every 1 100 second and produces an interrupt when it reaches the value stored in the Periodic Interrupt Modulus register. The Counter register is then reset and counting continues. Operation is started by writing a non-zero value to the Modulus register. Writing a zero will stop interrupt generation immediately and will halt the Periodic Interrupt Counter after 2.55 seconds. The Modulus register is write-only, the Counter register can only be read. Both registers have the same index address (05H). 7.30 Received call delay
Call reception causes both the Periodic Interrupt Modulus and the Counter register to be reset. Since the Periodic Interrupt Counter runs for another 2.55 seconds after a reset, the received call delay (in 1100 second units) can be determined by reading the Counter register.
1997 Jun 24
19
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
Table 18 Alert set-up register (04H; write) BIT (MSB: D7) D0 D1 D2 D3 D4 D5 VALUE 0 1 0 1 0 1 1 1 1 00 D7 and D6(1) 01 10 11 Note DESCRIPTION call alert via cadence register POCSAG call alert (pattern selected by D7, D6)
PCD5003
LOW level acoustic alert (ATL), pulsed vibrator alert (25 Hz) HIGH level acoustic alert (ATL + ATH), continuous vibrator alert normal alerts (acoustic and LED) warbled alerts: 16 Hz (LED: on/off, ATL/ATH: alternate fAWH, fAWL) acoustic alerts enable (ATL, ATH) vibrator alert enabled (VIB) LED alert enabled (LED) POCSAG alert pattern FC = 00, see Fig.8(a) POCSAG alert pattern FC = 01, see Fig.8(b) POCSAG alert pattern FC = 10, see Fig.8(c) POCSAG alert pattern FC = 11, see Fig.8(d)
1. Bits D7 and D6 correspond to function bits 20 and 21 respectively in the address codeword, which designate the POCSAG call type as shown in Table 1.
D7, D6
handbook, full pagewidth
00
(a) 01 (b) 10 (c) 11 (d)
MLC251
Fig.8 POCSAG alert patterns.
1997 Jun 24
20
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
7.31 Alert generation
PCD5003
interrupt occurs at the start of the 8th cadence time slot. Since D1 acts immediately on the alert level, it is advised to reset the last bit of the previous pattern to prevent unwanted audible level changes. 7.34 Vibrator alert
The PCD5003 is capable of controlling 3 different alert transducers: acoustic beeper (HIGH and LOW level), LED and vibrator motor. The associated outputs are ATH/ATL, LED and VIB respectively. ATL is an open drain output capable of directly driving an acoustic alerter via a resistor. The other outputs require external transistors. Each alert output can be individually enabled via the alert set-up register. Alert level and warble can be separately selected. The alert pattern can either be standard POCSAG or determined via the alert cadence register. Direct alert control is possible via input ALC. The alert set-up register is shown in Table 18. Standard POCSAG alerts can be selected by setting bit D0 in the alert set-up register, bits D6 and D7 determining the alert pattern used. Automatic generation via all alert outputs of the POCSAG alert pattern matching the received call type can be enabled by SPF programming (SPF byte 03, bit D2). 7.32 Alert cadence register (03H; write)
The vibrator output (VIB) is activated continuously during a standard POCSAG alert or whenever the alert cadence register is non-zero. Two alert levels are supported: LOW level (25 Hz square-wave) and HIGH level (continuous). The vibrator level is controlled by bit D1 in the alert set-up register. 7.35 LED alert
The LED output pattern corresponds either to the selected POCSAG alert or to the contents of the alert cadence register. No equivalent exists for HIGH/LOW level alerts. 7.36 Warbled alert
When not programmed for POCSAG alerts (alert set-up register bit D0 = 0), the 8-bit alert cadence register determines the alert pattern. Each bit represents a 62.5 ms time slot, a logic 1 activating the enabled alert transducers. The bit pattern is rotated with the MSB (bit D7) being output first and the LSB (bit D0) last. When the last time slot (bit D0) is started an interrupt is generated to allow loading of a new pattern. When the pattern is not changed it will be repeated. Writing a zero to the alert cadence register will halt alert generation. 7.33 Acoustic alert
When enabled by setting bit D2 in the alert set-up register, the signals on outputs ATL, ATH and LED are warbled with a 16 Hz modulation frequency. Output LED is switched on and off at the modulation rate, while outputs ATL and ATH switch between fAWH and fAWL alerter frequencies. 7.37 Direct alert control
A direct alert control input (ALC) is available for generating user alarm signals (e.g. battery-low warning). A HIGH level on input ALC activates all enabled alert outputs, overruling any ongoing alert patterns. 7.38 Alert priority
Acoustic alerts are generated via outputs ATL and ATH. For LOW level alerts only ATL is active, while for HIGH level alerts ATH is also active. ATL is driven in counter phase with ATH. The alert level is controlled by bit D1 of the alert set-up register. When D1 is reset, for standard POCSAG alerts (D0 = 1) a LOW level acoustic alert is generated during the first 4 seconds (ATL), followed by 12 seconds at HIGH level (ATL + ATH). When D1 is set, the full 16 seconds are at HIGH level. An interrupt is generated upon expiry of the full alert time. When using the alert cadence register, D1 would normally be updated by external control when the alert time-out 1997 Jun 24 21
Generation of a standard POCSAG alert (D0 = 1) overrides any alert pattern in the alert cadence register. After completion of the standard alert, the original cadence is restarted from the position it was left at. The alert set-up register will now contain the settings for the standard alert. The highest priority has been assigned to the alert control input (ALC). All enabled alert outputs will be activated while ALC is set. Outputs are activated/deactivated synchronous with the decoder clock. Activation requires an extra delay of 1 clock when no alerts are being generated. When input ALC is reset, acoustic alerting does not cease until the current output frequency cycle has been completed.
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
7.39 Cancelling alerts
PCD5003
When enabled by SPF programming (SPF byte 03, bit D2) standard POCSAG alerts will automatically be generated on outputs ATL, ATH, LED and VIB upon call reception. The alert pattern matches the call type as indicated by the function bits in the received address codeword. The original settings of the alert set-up register will be lost. Bit D0 is reset after completion of the alert.
Standard POCSAG alerts (manual or automatic) are cancelled by resetting bit D0 in the alert set-up register. User defined alerts are cancelled by writing a zero to the alert cadence register. Any ongoing alert is cancelled when a reset pulse is applied to input RST. 7.40 Automatic POCSAG alerts
Standard alert patterns have been defined for each POCSAG call type, as indicated by the function bits in the address codeword (see Table 1). The timing of these alert patterns is shown in Fig.9.
handbook, full pagewidth
FC = 00 t ALC FC = 01 t ALP t ALP t ALP
t ALC FC = 10 t ALC FC = 11
t ALP
t ALP
t ALC
t ALC
t ALP
t ALP
MLC252
Fig.9 POCSAG alert timing.
1997 Jun 24
22
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
7.41 SRAM access 7.44
PCD5003
RAM data output register (09H; read)
The on-chip SRAM can hold up to 96 bytes of call data. Each call consists of a call header (3 bytes), message data blocks (3 bytes per codeword) and a call terminator (3 bytes). The RAM is filled by the decoder and can be read via the I2C-bus interface. The RAM is accessed indirectly by means of a read address pointer and a data output register. A write address pointer indicates the first byte after the last message byte stored. Status register bit D2 is set when the read and write pointers are different. It is reset only when the SRAM pointers become equal during reading, i.e. when the RAM becomes empty. Status bit D3 is set when the read and write pointers become equal. This can be due to a RAM empty or a RAM full condition. It is reset after a status read operation. Interrupts are generated as follows: * When status bit D2 is set and the receiver is disabled (RXE = 0): data is available for reading * Immediately when status bit D3 is set: RAM is either empty (status bit D2 = 0) or full (status bit D2 = 1). To avoid loss of data due to RAM overflow at least 3 bytes of data must be read during reception of the codeword following the `RAM full' interrupt. 7.42 RAM write address pointer (06H; read)
The RAM data output register contains the byte addressed by the RAM read address pointer. It can only be read, each read operation causing an increment of the RAM read address pointer. 7.45 EEPROM access
The EEPROM is intended for storage of user addresses (RICs), sync words and special programmed function (SPF) bits representing the decoder configuration. The EEPROM can store 48 bytes of information and is organized as a matrix of 8 rows by 6 columns. The EEPROM is accessed indirectly via an address pointer and a data I/O register. The EEPROM is protected against inadvertent writing by means of the programming enable bit in the control register (bit D1). The EEPROM memory map is non-contiguous as can be seen in Fig.10, which shows both the EEPROM organization and the access method. Identifier locations contain RICs or sync words. A total of 20 unassigned bytes is available for general purpose storage. 7.46 EEPROM address pointer (07H; read/write)
The RAM write address pointer is automatically incremented during call reception, as the decoder writes each data byte to RAM. The RAM write address pointer can only be read. Values range from 00H to 5FH. Bit D7 (MSB) is not used and its value is undefined when read. 7.43 RAM read address pointer (08H; read/write)
An EEPROM location is addressed via the EEPROM address pointer. It is incremented automatically each time a byte is read or written via the EEPROM data I/O register. The EEPROM address pointer contains two counters, for the row and the column number. Bits D2 to D0 contain the column number (0 to 5) and bits D5 to D3 the row number (0 to 7). Bits D7 and D6 of the address pointer are not used. Data written to these bits will be ignored, while their values are undefined when read. The column and row counters are connected in series. Upon overflow of the column counter (column = 5) the row counter is automatically incremented and the column counter wraps to 0. On overflow the row counter wraps from 7 to 0. 7.47 EEPROM data I/O register (0AH; read/write)
The RAM read address pointer is automatically incremented after reading a data byte via the RAM output register. It can be accessed for writing as well as reading. The values range from 00H to 5FH. When at 5FH a read operation will cause wrapping around to 00H. Bit D7 (MSB) is not used; it is ignored when written and undefined when read.
The byte addressed by the EEPROM address pointer can be written or read via the EEPROM Data I/O register. Each access automatically increments the EEPROM address pointer.
1997 Jun 24
23
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
7.48 EEPROM access limitations
PCD5003
After writing each block a pause of maximum 7.5 ms is required to complete the programming operation internally. During this time the external microcontroller may generate an I2C-bus stop condition. If another I2C-bus transfer is started the decoder will pull SCL LOW during this pause. After writing the EEPROM programming enable bit (D1) in the control register must be reset. 7.51 Invalid write address
Since the EEPROM address pointer is used during data decoding, the EEPROM may not be accessed while the receiver is active (RXE = 1). It is advised to switch to OFF state before accessing the EEPROM. The EEPROM cannot be written unless the EEPROM programming enable bit (bit D1) in the control register is set. For writing a minimum supply voltage VPG is required (2.0 V typ.). The supply current needed during writing (IPG) will be 500 A. Any modified SPF settings (bytes 0 to 3) only take effect after a decoder reset. Modified identifiers are active immediately. 7.49 EEPROM read operation
When an invalid write address is used, the column counter bits (D2 to D0) are forced to zero before being loaded into the address pointer. The row counter bits are used normally. 7.52 Incomplete programming sequence
EEPROM read operations must start at a valid address in the non-contiguous memory map. Single-byte or block reads are permitted. 7.50 EEPROM write operation
A programming sequence may be aborted by an I2C-bus stop condition. Next, the EEPROM programming enable bit (D1) in the control register must be reset. Any bytes received of the last 6-byte block will be ignored and the contents of this (incomplete) EEPROM block will remain unchanged. 7.53 Unused EEPROM locations
EEPROM write operations must always take place in blocks of 6 bytes, starting at the beginning of a row. Programming a single byte will reset the other bytes in the same row. Modifying a single byte in a row requires re-writing the unchanged bytes with their old contents.
A total of 20 EEPROM bytes is available for general purpose storage (see Table 19).
handbook, full pagewidth
0 0 1 2 ROW 3 4 5 6 7 I D 1
1
COLUMN 2 3
4
5 D7 0
ADDRESS POINTER
D0 1 0 0
1
0
I D 2
I D 3
I D 4
I D 5
I D 6 D7 I/O REGISTER D0 ROW COLUMN
SPF bits
Synthesizer data
Identifiers
unused bytes
MLC254
Fig.10 EEPROM organization and access.
1997 Jun 24
24
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
Table 19 Unused EEPROM addresses ROW 0 5 6 7 Note 1. When using bytes 04H and 05H, care must be taken to preserve the SPF information stored in bytes 00H to 03H. HEX 04 and 05(1) 28 to 2D 30 to 35 38 to 3D 7.54
PCD5003
Special programmed function allocation
The SPF bit allocation in the EEPROM is shown in Tables 20 to 24. The SPF bits are located in row 0 of the EEPROM and occupy 4 bytes. Bytes 04H and 05H are not used and are available for general purpose storage. The contents of SPF (bytes 0 to 3) are read into the associated logic only when the decoder is reset (HIGH level in input RST).
Table 20 Special Programmed Functions (EEPROM address 00H) BIT (MSB: D7) D0 D1 D2 D3 D4 D5 D6 D7 VALUE X X X X X X X 1 DESCRIPTION reserved for future use; logic 0 when read reserved for future use reserved for future use reserved for future use reserved for future use reserved for future use reserved for future use; logic 0 when read received data inversion enabled
Table 21 Special Programmed Functions (EEPROM address 01H) BIT (MSB: D7) VALUE 00 D1 and D0 01 10 11 00 D3 and D2 01 10 11 00 D5 and D4 01 10 11 D6 D7 Note 1. Since the exact establishment time is related to the programmed bit rate, Table 22 shows the values for the various bit rates. 1997 Jun 24 25 1 1 10 ms 15 ms 30 ms 20 ms oscillator establishment time (nominal); note 1 30 ms 40 ms 50 ms 512 bits/s received bit rate 1024 bits/s (not used in POCSAG) 1200 bits/s 2400 bits/s synthesizer interface enabled (data is output via ZSD, ZSC and ZLE at decoder switch-on) voltage converter enabled DESCRIPTION 5 ms receiver establishment time (nominal); note 1
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
Table 22 Establishment time as a function of bit rate NOMINAL ESTABLISHMENT TIME 5 ms 10 ms 15 ms 20 ms 30 ms 40 ms 50 ms ACTUAL ESTABLISHMENT TIME 512 bits/s 5.9 ms (3 bits) 11.7 ms (6 bits) 15.6 ms (8 bits) 23.4 ms (12 bits) 31.2 ms (16 bits) 39.1 ms (20 bits) 46.9 ms (24 bits) 1024 bits/s 5.9 ms (6 bits) 11.7 ms (12 bits) 15.6 ms (16 bits) 23.4 ms (24 bits) 31.2 ms (32 bits) 39.1 ms (40 bits) 46.9 ms (48 bits) 1200 bits/s 5.0 ms (6 bits) 10.0 ms (12 bits) 16.7 ms (20 bits) 20.0 ms (24 bits) 26.7 ms (32 bits) 40.0 ms (48 bits) 53.3 ms (64 bits)
PCD5003
2400 bits/s 5.0 ms (12 bits) 10.0 ms (24 bits) 16.7 ms (40 bits) 20.0 ms (48 bits) 26.7 ms (64 bits) 40.0 ms (96 bits) 53.3 ms (128 bits)
Table 23 Special Programmed Functions (EEPROM address 02H) BIT (MSB: D7) D0 D1 VALUE X X 00 D3 and D2 01 10 11 D4 D5 D7 and D6 1 0 XX not used not used 32768 Hz real time clock reference 50 Hz square-wave 2 Hz
1 60 Hz
DESCRIPTION
signal test mode enabled (REF and INT outputs) burst error correction enabled reserved for future use
Table 24 Special Programmed Functions (EEPROM address 03H) BIT (MSB: D7) VALUE 00 D1 and D0 01 10 11 D2 D3 D4 D5 D6 D7 1 X X X 0 1 X 2731 Hz 4096 Hz 3200 Hz automatic POCSAG alert generation enabled not used not used not used INT output polarity: active LOW INT output polarity: active HIGH not used DESCRIPTION 2048 Hz acoustic alerter frequency
1997 Jun 24
26
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
7.55 Synthesizer programming data
PCD5003
Identifiers are stored in EEPROM rows 2, 3 and 4. Each identifier location consists of 3 bytes in the same column. The identifier number is equal to the column number + 1. Only the last 4 identifiers (numbers 3 to 6) can be programmed as a UPSW. Identifiers 1 and 2 always represent RICs. A UPSW represents an unused address and must differ by more than 6 bits from preamble to guarantee detection. The standard POCSAG sync word is always enabled and has identifier number 7. Table 26 shows the memory locations of the 6 identifiers. The bit allocation per identifier is given in Table 27.
Data for programming a PLL synthesizer via pins ZSD, ZSC and ZLE can be stored in row 1 of the EEPROM. Six bytes are available starting from address 08H. Data is transferred in two serial blocks of 24 bits each, starting with bit 0 (MSB) of block 1. Any unused bits must be programmed at the beginning of a block. 7.56 Identifier storage allocation
Up to 6 different identifiers can be stored in EEPROM for matching with incoming data. The PCD5003 can distinguish two types of identifiers: * User addresses (RIC) * User Programmable Sync Words (UPSW).
Table 25 Synthesizer programming data (EEPROM address 08H to 0DH) ADDRESS (HEX) 08 09 0A 0B 0C 0D BIT (MSB: D7) D7 to D0 D7 to D0 D7 to D0 D7 to D0 D7 to D0 D7 to D0 bits 8 to 15 bits 16 to 23 bits 0 to 7 of data block 2 (bit 0 is MSB) bits 8 to 15 bits 16 to 23 DESCRIPTION bits 0 to 7 of data block 1 (bit 0 is MSB)
Table 26 Identifier storage allocation (EEPROM address 10H to 25 H) ADDRESS (HEX) 10 to 15 18 to 1D 20 to 25 BYTE 1 2 3 identifier number 1 to 6 identifier number 1 to 6 identifier number 1 to 6 DESCRIPTION
1997 Jun 24
27
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
Table 27 Identifier bit allocation BYTE 1 2 BIT (MSB: D7) D7 to D0 D7 to D0 D7 and D6 D5 D4 3 D3 D2 D1 D0 Notes 1. The bit numbering corresponds with the numbering in a POCSAG codeword: bit 1 is the flag bit (0 = address, 1 = message). bits 10 to 17 bits 18 and 19 frame number bit FR3 (RIC); note 3 frame number bit FR2 (RIC) frame number bit FR1 (RIC) identifier type selection (0 = UPSW, 1 = RIC); note 4 identifier enable (1 = enabled) reserved for future use, logic 0 when read DESCRIPTION
PCD5003
bits 2 to 9 of POCSAG codeword (RIC or UPSW); notes 1 and 2
2. A UPSW needs 18 bits to be matched for successful identification. Bit 1 (MSB) must be logic 0; bits 2 to 19 contain the identifier bit pattern; they are followed by 2 predetermined random (function) bits and the UPSW is completed by 10 CRC error correction bits and an even-parity bit. 3. Bits FR3 to FR1 (MSB: FR3) contain the 3 least significant bits of the 21-bit RIC. 4. Identifiers 1 and 2 (RIC only) will be disabled by programming bit D2 as logic 0. 7.57 Voltage doubler The level-shifted interface lines are: RST, DON, ALC, REF, INT. The I2C-bus interface lines SDA and SCL can be level-shifted independently of VPR by means of the standard external pull-up resistors. 7.59 7.58 Level-shifted interface All interface lines are suited for communication with a microcontroller operating from a higher supply voltage. The external device must have a common reference at VSS of the PCD5003. The reference voltage for the level-shifted interface must be applied to input VPR. This could be the on-chip voltage doubler output VPO if required. When the microcontroller has a separate (regulated) supply this separate supply voltage should be connected to VPR. Signal test mode
An on-chip voltage doubler provides an unregulated DC output for supplying an LCD or a low power microcontroller on output VPO. An external ceramic capacitor of typical 100 nF is required between pins CCN and CCP. The voltage doubler is enabled via SPF programming.
A special `signal test' mode is available for monitoring the performance of a receiver circuit together with the front-end of the PCD5003. For this purpose the output of the digital noise filter and the recovered bit clock are made available at outputs REF and INT respectively. All synchronization and decoding functions are normally active. The `signal test' mode is activated/deactivated by SPF programming.
1997 Jun 24
28
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
8 8.1 OPERATING INSTRUCTIONS Reset conditions
PCD5003
A more accurate reset duration can be realised with an additional external resistor connected to VSS. Recommended minimum values in this case are C = 2.2 nF and R = 100 k (see Fig.15). 8.3 Reset timing
When the PCD5003 is reset by applying a HIGH-level on input RST, the condition of the decoder is as follows: * OFF status (irrespective of DON input level) * REF output frequency 32768 Hz * All internal counters reset * Status/control register reset * INT output at LOW-level * No alert transducers selected * LED, VIB and ATH outputs at LOW level * ATL output high impedance * SDA, SCL inputs high impedance * Voltage converter disabled. Within tRSU after release of the reset condition (RST LOW) the programmed functions are activated. The settings affecting the external operation of the PCD5003 are as follows: * REF output frequency * Voltage converter * INT output polarity * Signal test mode. When input DON is HIGH, the decoder starts operating in ON status immediately following tRSU. 8.2 Power-on reset circuit
The start-up time for the crystal oscillator may exceed 1 second (typ. 800 ms). It is advised to apply a reset condition at least during the first part of this period. The minimum reset pulse duration tRST is 50 s. During reset the oscillator is active, but clock signals are inhibited internally. Once the reset condition is released the end of the oscillator start-up period can be detected by a rising edge on output INT. During a reset the voltage converter clock (Vclk) is held at zero. The resulting output voltage drop may cause problems when the external resetting device is powered by the internal voltage doubler. A sufficiently large buffer capacitor between output VPO and VSS must be provided to supply the microcontroller during reset. The voltage at VPO will not drop below VDD - 0.7 V. Immediately after a reset all programmable internal functions will start operating according to a programmed value of 0. During the first 8 full clock cycles (tRSU) all programmed values are loaded from EEPROM. After reset the receiver outputs RXE and ROE become active immediately, if DON is HIGH and the synthesizer is disabled. When the synthesizer is enabled, RXE and ROE will only become active after the second pulse on ZLE completes the loading of synthesizer data. The full reset timing is shown in Fig.11. The start-up timing including synthesizer programming is given in Fig.12. 8.4 Initial programming
During power-up of the PCD5003 a HIGH level of minimum duration tRST = 50 s must be applied to pin RST. This is to prevent EEPROM corruption which might otherwise occur because of the undefined contents of the Control register. The reset signal can be applied by the external microcontroller or by an RC power-on reset circuit on pin RST (C to VPR, R to VSS). Such an RC-circuit should have a time constant of at least 3tRST = 150 s. Input RST has an internal high-ohmic pull-down resistor (nominal 2 M at 2.5 V supply) which could be used together with a suitable external capacitor connected to VPR to create a power-on reset signal. However, since this pull-down resistor varies considerably with processing and supply voltage, the resulting time constant is inaccurate.
A newly-delivered PCD5002 has EEPROM contents which are undefined. The EEPROM should therefore be programmed, followed by a reset to activate the SPF settings, before any attempt is made to use the device.
1997 Jun 24
29
Product specification
PCD5003
Fig.11 Reset timing.
handbook, full pagewidth
1997 Jun 24
t RST programmed for 32768 Hz
Philips Semiconductors
XTAL1
RST
asynchronous
REF
Advanced POCSAG Paging Decoder
INT
active LOW active HIGH
active LOW active HIGH
30
(1) (2)
Vclk
RXE
(DON = 1)
ZLE t RSU
MLC253
(1) The RXE output signal is shown for disabled synthesizer. When the synthesizer is enabled RXE is held off until after the second pulse on ZLE (programming complete). (2) The ZLE output signal is shown for enabled synthesizer and DON = 1. When DON = 0 output ZLE remains HIGH until ON state is entered (DON = 1 or control register bit D4 = 1).
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
PCD5003
handbook, full pagewidth
DON
ZSC
BLOCK 1
BLOCK 2
ZLE t ZDL1 tZDL2 t p RXE t ZSU t OSU t clk
MLC255
t ZDL1
Fig.12 Start-up timing including synthesizer programming.
9 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). SYMBOL VDD VPR Vn Vn1 Ptot PO Tamb Tstg supply voltage external reference voltage input voltage on any other pin total power dissipation power dissipation per output operating ambient temperature storage temperature VPR VDD - 0.8 V Vn1 7.0 V voltage on pins ALC, DON, RST, SDA and SCL Vn 7.0 V PARAMETER CONDITIONS MIN. -0.5 -0.5 VSS - 0.8 VSS - 0.8 - - -25 -55 MAX. +7.0 +7.0 VPR + 0.8 VDD + 0.8 250 100 +70 +125 V V V V mW mW C C UNIT
1997 Jun 24
31
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
10 DC CHARACTERISTICS VDD = 2.7 V; VPR = 2.7 V; VSS = 0 V; Tamb = -25 to +70 C; unless otherwise specified. SYMBOL Supply VDD VPR IDD0 IDD1 VPG IPG Inputs VIL LOW level input voltage RDI, BAT DON, ALC, RST SDA, SCL VIH HIGH level input voltage RDI, BAT DON, ALC, RST SDA, SCL IIL LOW level input current pins RDI, BAT,TS1, TS2, DON, ALC and RST HIGH level input current TS1, TS2 RDI, BAT RDI, BAT DON, ALC, RST Outputs IOL LOW level output current VIB, LED ATH INT, REF ZSD, ZSC, ZLE ATL ROE, RXE Tamb = 25 C VOL = 0.3 V VOL = 0.3 V VOL = 0.3 V VOL = 0.3 V VOL = 1.2 V; note 2 VOL = 0.3 V 80 250 80 70 13 80 - - - - 27 - Tamb = 25 C; VI = VSS 0.7VDD 0.7VPR 0.7VDD 0 - - - - VSS VSS VSS - - - supply voltage supply current (OFF) supply current (ON) programming supply voltage programming supply current voltage converter disabled note 1 note 1; DON = VDD voltage converter disabled voltage converter enabled 1.5 1.5 - - 2.0 2.0 - 2.7 2.7 25.0 50.0 - - - PARAMETER CONDITIONS MIN. TYP.
PCD5003
MAX.
UNIT
6.0 6.0 40.0 80.0 6.0 3.0 800
V V A A V V A
external reference voltage input VPR VDD - 0.8 V
0.3VDD 0.3VPR 0.3VDD VDD VPR VPR -0.5
V V V V V V A
IIH
Tamb = 25 C VI = VDD VI = VDD; RXE = 0 VI = VDD; RXE = 1 VI = VPR 6 6 0 250 - - - 500 20 20 0.5 850 A A A nA
- - - - 55 -
A A A A mA A
1997 Jun 24
32
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
PCD5003
SYMBOL IOH
PARAMETER HIGH level output current VIB, LED ATH INT, REF ZSD, ZSC, ZLE ATL ROE, RXE
CONDITIONS Tamb = 25 C VOH = 0.7 V VOH = 0.7 V VOH = 2.4 V VOH = 2.4 V ATL high-impedance; note 3 VOH = 2.4 V
MIN. -0.6 -3.0 -80 -60 - -600 - - - - - -
TYP.
MAX. -2.4 -11.0 - - -0.5 -
UNIT mA mA A A A A
Notes 1. Inputs: SDA and SCL pulled up to VDD; all other inputs connected to VSS. Outputs: RXE and ROE logic 0; REF: fref = 160 Hz; all other outputs open-circuit. Oscillator: no crystal; external clock fosc = 76800 Hz; amplitude: VSS to VDD. Voltage convertor disabled (SPF byte 01, bit D7 = 0; see Table 21). 2. Maximum output current is subject to absolute maximum ratings per output (see Chapter 9). 3. When ATL (open drain output) is not activated it is high impedance. 11 DC CHARACTERISTICS (WITH VOLTAGE CONVERTER) VDD = 2.7 V; VSS = 0 V; VPR = VPO; Tamb = -25 to +70 C; Cs = 100 nF; voltage converter enabled. SYMBOL VDD VPO(0) VPO IPO PARAMETER supply voltage output voltage; no load output voltage output current VDD = 2.7; IPO = 0 VDD = 2.0 V; IPO = -250 A VDD = 2.0 V; VPO = 2.7 V VDD = 3.0 V; VPO = 4.5 V CONDITIONS - 3.0 -400 -650 MIN. 1.5 - 5.4 3.5 -650 -900 TYP. MAX. 3.0 - - - - UNIT V V V A A
12 OSCILLATOR CHARACTERISTICS Quartz crystal type: MX-1V or equivalent. Quartz crystal parameters: f = 76 800 Hz; RS(max) = 35 k; CL = 8 pF; C0 = 1.4 pF; C1 = 1.5 fF. Maximum overall tolerance: 200 x 10-6 (includes: cutting, temperature, aging). SYMBOL CXO gm PARAMETER output capacitance XTAL2 oscillator transconductance VDD = 1.5 V CONDITIONS - 6 MIN. TYP. 10 12 MAX. - - UNIT pF S
13 EEPROM CHARACTERISTICS SYMBOL NEW tDR Note 1. Retention cannot be guaranteed for naked dies (PCD5003U/10). PARAMETER erase/write cycles data retention time Tamb = +70 C; note 1 CONDITIONS MIN. 1000 10 - TYP. 10000 MAX. - - years UNIT
1997 Jun 24
33
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
14 AC CHARACTERISTICS VDD = 2.7 V; VSS = 0 V; VPR = 2.7 V; Tamb = 25 C;. fosc = 76800 Hz. SYMBOLS System clock Tclk fAL system clock period fosc = 76800 Hz SPF byte 03H; bits: D1, D0 = 0 0 D1, D0 = 0 1 D1, D0 = 1 0 D1, D0 = 1 1 fAW fAWH fAWL fVBP warbled alert; modulation frequency warbled alert; high acoustic alert frequency warbled alert; low acoustic alert frequency pulsed vibrator frequency (square-wave) alert set-up bit D2 = 1; outputs ATL, ATH, LED alert set-up bit D2 = 1; outputs ATL, ATH alert set-up bit D2 = 1; outputs ATL, ATH low-level alert - - - - - - - - 2048 2731 3200 4096 16 fAL
1 2fAL
PCD5003
PARAMETER
CONDITIONS -
MIN.
TYP.
MAX. -
UNIT s
13.02
Call alert frequencies alert frequency - - - - - - - - Hz Hz Hz Hz Hz Hz Hz Hz
25
Call alert duration tALT tALL tALH tVBL tVBH tALC tALP fref alert time-out period ATL output time-out period ATH output time-out period VIB output time-out period VIB output time-out period alert cycle period alert pulse duration low-level alert high-level alert low -level alert high-level alert - - - - - - - 16 4 12 4 12 1 125 - - - - - - - s s s s s s ms
Real time clock reference real time clock reference frequency SPF byte 02H; bits: D3, D2 = 0 0; note 1 D3, D2 = 0 1; note 2 D3, D2 = 1 0 D3, D2 = 1 1 tRFP real time clock reference pulse duration - - - - 32768 50 2
1 60
- - - - -
Hz Hz Hz Hz s
all reference frequencies except - 50 Hz (square-wave)
13.02
1997 Jun 24
34
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
PCD5003
SYMBOLS Receiver control tRXT tRXON
PARAMETER
CONDITIONS - - - - - - - - -
MIN.
TYP.
MAX. - - - - - - - - -
UNIT
RXE, ROE transition time RXE establishment time (nominal values: actual duration is bit rate dependent, see Table 22)
CL = 5 pF SPF byte 01H; bits: D1, D0 = 0 0 D1, D0 = 0 1 D1, D0 = 1 0 D1, D0 = 1 1
100 5 10 15 30 20 30 40 50 - - - - - - - - - - - - - - - - -
ns ms ms ms ms ms ms ms ms
tROON
ROE establishment time (nominal values: actual duration is bit rate dependent, see Table 22)
SPF byte 01H; bits: D3, D2 = 0 0 D3, D2 = 0 1 D3, D2 = 1 0 D3, D2 = 1 1
I2C-bus fSCL tLOW tHIGH tSU;DAT tHD;DAT tr tf CB tSU;STA tHD;STA tSU;STO Reset tRST tRSU tOSU
interface SCL clock frequency SCL clock low period SCL clock HIGH period data set-up time data hold time SDA, SCL rise time SDA, SCL fall time capacitive bus line load START condition set-up time START condition hold time STOP condition set-up time 0 1.3 0.6 100 0 - note 3 - 0.6 0.6 0.6 400 - - - - 300 300 400 - - - - 105 4 kHz s s ns ns ns ns pF s s s s s ms s
external reset duration set-up time after reset set-up time after switch-on oscillator running oscillator running
50 - - - tBIT tBIT
Data input tTDI tDI1 tDI0 fDI tBIT tCW tPA tBAT data input transition time data input logic 1 duration data input logic 0 duration see Fig.13 see Fig.13 see Fig.13 100 - - - - -
POCSAG data timing (512 bits/s) data input rate bit duration codeword duration preamble duration batch duration SPF byte 01H; bits D5, D4 = 0 0 - - - 1125 - 512 1.9531 62.5 - 1062.5 bits/s ms ms ms ms
1997 Jun 24
35
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
PCD5003
SYMBOLS
PARAMETER
CONDITIONS SPF byte 01H; bits D5, D4 = 1 0 - - -
MIN.
TYP.
MAX. - - - - - - - - - -
UNIT
POCSAG data timing (1200 bits/s) fDI tBIT tCW tPA tBAT fDI tBIT tCW tPA tBAT tZSU fZSC tZCL tZSD tZDS tZDL1 tZLE tZDL2 Notes 1. 32768 Hz reference signal: 32 pulses per 75 clock cycles, alternately separated by 1 or 2 pulse periods (pulse duration: tRFP). The timing is shown in Fig.14. 2. 50 Hz reference signal: square-wave. 3. The fall time may be faster than prescribed in the I2C-bus specification for very low load capacitance values. To increase the fall time external capacitance is required. 4. Duration depends on programmed bit rate; after reset tZSU = 1.5 bits. 5. Nominal values; pause in 12th data bit (see Table 12). data input rate bit duration codeword duration preamble duration batch duration 1200 833.3 26.7 - 453.3 bits/s s ms ms ms
480 - SPF byte 01H; bits D5, D4 = 1 1 - - - 240 -
POCSAG data timing (2400 bits/s) data input rate bit duration codeword duration preamble duration batch duration 2400 416.6 13.3 - 226.6 - 38400 13.02 26.04 13.02 91.15 13.02 117.19 bits/s s ms ms ms
Synthesizer control synthesizer set-up duration output clock frequency clock pulse duration data bit duration data bit set-up time data load enable delay load enable pulse duration inter block delay note 5 oscillator running; note 4 note 5 1 - - - - - - - 2 - - - - - - - bits Hz s s s s s s
1997 Jun 24
36
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
PCD5003
handbook, halfpage
tDI1
tDI0
t TDI
MGL100
Fig.13 Data input timing.
handbook, full pagewidth
t RFP
t RFP
2t RFP
MLC278
Fig.14 Timing of the 32 768 Hz reference signal.
1997 Jun 24
37
BATTERY POSITIVE
M
(1) Value depends on number of devices attached. (2) Values should be chosen to give a time constant of at least 150 s. C = 2.2 nF and R = 100 k are recommended.
Product specification
PCD5003
Fig.15 Typical application example (display pager).
handbook, full pagewidth
1997 Jun 24
Cs 100 nF
(2) (1) (1)
Philips Semiconductors
4.7 k VIB LED VDD CCP CCN VPO VPR RST
(2)
4.7 k V
10 F function keys
ANT
V
DATA OUT
ATL ATH RDI
15 APPLICATION INFORMATION
RECEIVER
BAT REF DON INT REF ALC SDA SCL MICROCONTROLLER
BAT
PWR CTRL
RXE
OSC
V
PCD5003 DECODER
VCO V
V
Advanced POCSAG Paging Decoder
PWR CTRL
ROE
FREQUENCY DATA SYNTHESIZER CLK V XTAL1 TS1 TS2 XTAL2 VSS
ZSD
38
76.8 kHz 2.2 M I2C-bus BATTERY NEGATIVE n.c. n.c. V
ZSC LCD DRIVER V LCD LCD DRIVER V
MLC256
LATCH
ZLE
V
10 pF
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
16 PACKAGE OUTLINE LQFP32: plastic low profile quad flat package; 32 leads; body 7 x 7 x 1.4 mm
PCD5003
SOT358-1
c
y X
24 25
17 16 ZE
A
e E HE wM A A2 A 1
Q (A 3) bp Lp L
pin 1 index 32 1 e bp D HD wM B vM B 8 ZD vM A 9 detail X
0
2.5 scale
5 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.60 A1 0.20 0.05 A2 1.45 1.35 A3 0.25 bp 0.4 0.3 c 0.18 0.12 D (1) 7.1 6.9 E (1) 7.1 6.9 e 0.8 HD 9.15 8.85 HE 9.15 8.85 L 1.0 Lp 0.75 0.45 Q 0.69 0.59 v 0.2 w 0.25 y 0.1 Z D (1) Z E (1) 0.9 0.5 0.9 0.5 7 0o
o
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT358 -1 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION
ISSUE DATE 93-06-29 95-12-19
1997 Jun 24
39
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
17 SOLDERING 17.1 Introduction
PCD5003
If wave soldering cannot be avoided, the following conditions must be observed: * A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering technique should be used. * The footprint must be at an angle of 45 to the board direction and must incorporate solder thieves downstream and at the side corners. Even with these conditions, do not consider wave soldering LQFP packages LQFP48 (SOT313-2), LQFP64 (SOT314-2) or LQFP80 (SOT315-1). During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Maximum permissible solder temperature is 260 C, and maximum duration of package immersion in solder is 10 seconds, if cooled to less than 150 C within 6 seconds. Typical dwell time is 4 seconds at 250 C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. 17.4 Repairing soldered joints
There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "IC Package Databook" (order code 9398 652 90011). 17.2 Reflow soldering
Reflow soldering techniques are suitable for all LQFP packages. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Several techniques exist for reflowing; for example, thermal conduction by heated belt. Dwell times vary between 50 and 300 seconds depending on heating method. Typical reflow temperatures range from 215 to 250 C. Preheating is necessary to dry the paste and evaporate the binding agent. Preheating duration: 45 minutes at 45 C. 17.3 Wave soldering
Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 C.
Wave soldering is not recommended for LQFP packages. This is because of the likelihood of solder bridging due to closely-spaced leads and the possibility of incomplete solder penetration in multi-lead devices.
1997 Jun 24
40
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
18 DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Limiting values
PCD5003
This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications.
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. 19 LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 20 PURCHASE OF PHILIPS I2C COMPONENTS
Purchase of Philips I2C components conveys a license under the Philips' I2C patent to use the components in the I2C system provided the system conforms to the I2C specification defined by Philips. This specification can be ordered using the code 9398 393 40011.
1997 Jun 24
41
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
NOTES
PCD5003
1997 Jun 24
42
Philips Semiconductors
Product specification
Advanced POCSAG Paging Decoder
NOTES
PCD5003
1997 Jun 24
43
Philips Semiconductors - a worldwide company
Argentina: see South America Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. +61 2 9805 4455, Fax. +61 2 9805 4466 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 1 60 101, Fax. +43 1 60 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 689 211, Fax. +359 2 689 102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S, Tel. +45 32 88 2636, Fax. +45 31 57 0044 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615800, Fax. +358 9 61580920 France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex, Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427 Germany: Hammerbrookstrae 69, D-20097 HAMBURG, Tel. +49 40 23 53 60, Fax. +49 40 23 536 300 Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS, Tel. +30 1 4894 339/239, Fax. +30 1 4814 240 Hungary: see Austria India: Philips INDIA Ltd, Shivsagar Estate, A Block, Dr. Annie Besant Rd. Worli, MUMBAI 400 018, Tel. +91 22 4938 541, Fax. +91 22 4938 722 Indonesia: see Singapore Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3, 20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108, Tel. +81 3 3740 5130, Fax. +81 3 3740 5077 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA, Tel. +48 22 612 2831, Fax. +48 22 612 2327 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000, Tel. +27 11 470 5911, Fax. +27 11 470 5494 South America: Rua do Rocio 220, 5th floor, Suite 51, 04552-903 Sao Paulo, SAO PAULO - SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 829 1849 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 3 301 6312, Fax. +34 3 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 632 2000, Fax. +46 8 632 2745 Switzerland: Allmendstrasse 140, CH-8027 ZURICH, Tel. +41 1 488 2686, Fax. +41 1 481 7730 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2865, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel. +66 2 745 4090, Fax. +66 2 398 0793 Turkey: Talatpasa Cad. No. 5, 80640 GULTEPE/ISTANBUL, Tel. +90 212 279 2770, Fax. +90 212 282 6707 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 625 344, Fax.+381 11 635 777
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 (c) Philips Electronics N.V. 1997
Internet: http://www.semiconductors.philips.com
SCA54
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
437027/25/06/pp44
Date of release: 1997 Jun 24
Document order number:
9397 750 02433

▲Up To Search▲

Price & Availability of PCD5003

	To Download PCD5003 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .